1. LG G2 D802 Unlocked Motherboard. Item 6 Black For LG Optimus G2 D802 LCD Screen Display Touch Digitizer Repair + Frame - Black For LG. How To Clean USB Port On.
2. LG G2 LCD and Digitizer Replacement: This is a guide to repair your LG G2 Glass/LCD. But I have D802.

1. Lg G2 Usb Driver Download

For all LG smartphone user! Are you looking for LG USB Driver download link? Visit this page at AndroidRootGuide.com and get drivers for LG device!

Phone repair requires patience. Lots of patience. If you don't want to go through all of the steps listed, then do not attempt this repair. I believe any one can do this if they go SLOWLY and they PAY ATTENTION to what they're doing. Ribbon cables are our friends as long as we respect them.

I recommend using plastic spudgers for all ribbon cables. Be sure you're not touching the boards or any of the components on the boards. Hold all boards from the sides with your finger tips. Do not use metal prying tools inside of live phones unless you like dead phones.

Proceed with patience and good luck:). That little black piece that is outlined in red seems to be the environmental light sensor. The component itself will slide out of the black plastic holder, making it easier to position correctly when putting it all back together. When the author says it 'goes underneath' he means it faces the bottom of the phone, the same direction as the earphone connector. Note: the bottom board is glued or taped to the chassis, you can gently insert a flat plastic spudger underneath the board to ease it off the adhesive. Take your time and follow the guide and you'll do fine.

Read the guide, look at all the pictures, then carefully re-read each step and look at each picture in each step. There are a couple 'gotcha' boards/cables that you could destroy if you're not watching and being careful. It took me roughly 2.5 hours to do this because I was being extra careful and took some breaks to rest my eyes. Note: You'll need to get a roll of double-side phone tape to go with your new screen to stick it back to the frame. I accidentally ordered screen for D801, but I have D802, I didn't wanted to spend another fortune for the display assembly and I ordered lcd cable for D801 and hope it work's, but it weren't turning on, so I forced right side connector to the motherboard, it lighted up the display, but half of the touch weren't still working, so i tried to reconnect original cable (D802) but it didn't worked or if it did, it lighted up just for a moment, what could be the problem and how could I fix it? Please help me. Hello everyone, Maybe someone can help with an issue I been trying solve for a couple of days.

I have a Sprint LG G2 the Screen and LCD were cracked so I replaced both the LCD and the digitizer but when I reassembled the phone and power up everything looks fine but the digitizer is unresponsive. So disassembled and reassembled but I get the same results. So I thought maybe the part was defective so I contacted the part supplier and they sent me a new part and I'm getting the same results with the new part as well! I'm in need of some help.

I replaced the digitizer and Screen as one new unit on my wife's LG G2. At first it worked except the microphone wouldn't work and the proximity sensor was an issue. I found the proximity sensor gasket still in the old phone, disassembled, re-assembled with the gasket. And now it won't boot. It's gets to the LG screen and turns off. When I plug it in to the computer or charger, it just repeats the cycle,turns on, gets to the 'LG' screen, then turns off again, and continues to repeat. I been a cellphone tchnician for 9 years now with a company that gives services to 30+ stores.

Personally I have worked about 5 LG G2 that have presented this situation. I have observed that when SCREEN WORKS in other LG G2 but DOES NOT SHOW IMAGE on a certain LG G2, they have had some capacitors in front of the right Main Flex BOARD Connector in the Main Board. They are two black capacitors that are very fragile and can be easily damaged in any replacement process and will not be able to pass information from the Main Board to the LCD. This will give you NO IMAGE and can only be repaired by replacing those capacitors.

Will require soldering skills. I have not found those capacitors to buy then yet. Still, I have taken them from water damaged LG G2 Boards. Hope this illuminate your work! Thank you very much for your guide. The screen of my G2 stopped working: I have a black vertical band of few millimeters on one side of the screen.

The touchscreen works properly on the whole screen (also the black area) and the glass is perfectly intact (no crack in any place). Since both touchscreen and glass are intact I am starting to think that the problem is with the connector of the lcd to the board. Do you have any experience with this? Any advice on how I can troubleshoot? PICTURE in my profile image.

Needed to replace digitizer due to unresponsive touchscreen. Overall these instructions worked. My kit included LCD + digitizer in a frame so there were several other items that had to be moved to the new frame. Then I got the static/snow/multicolor dots. I had to reset one of the connectors. Then the screen would go black right after booting but in certain room lighting it worked. I found a tip about putting a folded piece of paper over the proximity sensor.

That also allowed knock on to work again. It's been working fine for a week now. It's time to speak out for your right to repair We have a chance to guarantee our right to repair electronic equipment—like smartphones, computers, and even farm equipment. This is a once-in-a-generation chance to protect local repair jobs—the corner mom-and-pop repair shops that keep getting squeezed out by manufacturers. Join the cause and tell your state representative to support Right to Repair. Tell them you believe repair should be fair, affordable, and accessible. Stand up for your right to repair!

In this tutorial we will show you how to root your LG G2 OPEN D802. For this to work you will need to enable the USB Debugging on your phone. To find out how to do this on newer Android Versions check out our Backup Tutorials Google automatically saves your contacts but doesn’t sync other files on your device. Check the following tutorials to completely backup your device. Easy root for LG G2 Supports the following carriers: ATT, TMO, VZW, KT, SKT, RGS, BELL, TLS and OPEN By IOMonster (thecubed on XDA) See for details. Original root idea from 320.8846/ Press any key to continue.

Looking for device Determining carrier Found ATT, TMO, SKT, or D802 phone! Pushing g2security 70 KB/s (288 bytes in 0.004s). Now, please unplug usb, go to developer options and disable USB debugging and re-enable it. Once you’ve done that, re-plug your usb. Press any key to continue. Waiting for device Now it’s time to install su and superuser. This will trip LG’s rootchecker!

This means your phone will show ROOTED in the settings menu, and in the LG Download mode. If you do not want to possibly invalidate your warranty press CTRL-C to stop this script. You will have a rooted ADB, but no apps on the phone will be able to access root functions. Press any key to continue. Mounting system RW and pushing SU, then remounting system RO again 1918 KB/s (96260 bytes in 0.049s) Installing superuser 2579 KB/s (1468798 bytes in 0.556s) pkg: /data/local/tmp/superuser.apk Success.

Lg G2 Usb Driver Download

Done. Please check the above for any errors and let me know if you run into any issues.

Enjoy your phone! Press any key to continue.

Phone not rooted. I tried obackup.it says phone not rooted.