Download Nestor Martin Manual
Nestor martin harmony manual (8.81MB) By Namiyo Oomura Download nestor martin harmony manual by Namiyo Oomura in size 8.81MB free nestor martin harmony manual kindle. Download and Read Nestor Martin Manual Nestor Martin Manual Make more knowledge even in less time every day. You may not always spend your time and money to go abroad. View and Download NESTOR MARTIN Harmony 1 operating instructions manual online. Harmony 1 Boiler pdf manual download.
. This Manual Must Always be Available to the Stove Operator Installation & Servicing Instructions Nestor Martin IQ13 Smoke Control IN1264 Edition A October 2012 Exempt PART NUMBER SERIAL NUMBER This manual must be used in conjunction with document IN1173.
The Wood and Mutlifuel Chimney. Table of Contents The Model Range Explained. 3 Technical Data, Intermittent Operation.5 Technical Data, Continuous Operation.5 General Technical Data.
5 IQ13 Aperture Size.5 IQ13 Dimensions. 6 Housing Construction, without an Existing Chimney Breast.8 Ideal installation.
Nestor David
The Model Range Explained Thank you for purchasing your stove and helping to protect our environment. Nestor Martin and Euroheat insist on progressive development to produce products which are market leading. Our aims are to produce stoves with the latest innovations, user friendly operation and highly efficient for lower cost operation.
When burning wood you will be greatly assisting with reducing CO². IMPORTANT The installation of this appliance must comply with all local regulations, including those referring to national and European Standards before it can be operated. The stove is not suitable for a shared flue. However, for England and Wales, only, the coming into force on 1st April 2002 of SI 2002 No 440 exempts the householder from this legal requirement for the installation of solid fuel fired appliance whose rated heat output is 50kW or less in a building having no more than 3 storeys (excluding any basement) if a Competent Engineer is employed who is registered under the Registration Scheme for Companies and Engineers involved in the Installation and Maintenance of.
Interval Efficiency Model Wood Wood Wood Smokeless Smokeless Smokeless Coal. Coal. Coal. 77.1% Net IQ13 Wood 5 kW 0.70 hr 70.2% Gross 77.1% Net 82.8% Net IQ13 Multifuel 5 kW 0.70 hr 3.5 kW 1.05 hr 70.2% Gross 75.4% Gross.
IQ13 Dimensions Dimensions mm Height 3 sided 50mm frame/25mm frame 605/580 Height 4 sided 50mm frame/25mm frame 626/576 Width of body Depth of body Height of body Height including flue spigot Front to heat vent outlet centre Front to flue outlet centre Flue diameter (internal diameter) Optional heat vent diameter (internal diameter) Centre between flue and heat vent. Supplied with the Stove Flue Spigot and Self-adhesive Rope Plexus Cover Plate Only used if fresh air kit is to be fitted Stove Operating and Ash Pan Tool 1 x Heat Resistant Leather Glove Fresh Air Spigot Only used if fresh air kit is Large Allen Key to be fitted Small Allen Key. Housing Construction, when Using an Existing Chimney Breast Whilst it is almost certain that the fabric of an existing fireplace and chimney will be non-combustible and will have a hearth which conforming to the regulations, should be inspected to ensure that it has not been modified by an over zealous “do it yourselfer”.
The stove’s flue spigot is fitted to the flue pipe by pushing it upwards from within the stove so that the flue can be positioned exactly, before in filling the fireplace to give the required housing size. A register plate should now be fitted. If a secondary lintel is to be fitted with only a single thickness of brick to be used as the closure, the inner face of the bricks should be faced with insulation material to reduce the temperature of the wall face. Rockwool, fibreglass or several layers of Glasrock are suitable.
Nestor Martin Oil Stove
Housing Construction, without an Existing Chimney Breast If the property has no existing chimney or chimney breast the first consideration will be the positioning of the flue. Taking the flue to the roof internally through the property will involve complying with many regulations and even an external flue may be subject to planning regulations. The insulating properties of many modern houses are extremely high and many external walls are now constructed with an inner skin of plasterboard, supported on a wooden frame which is thermally insulated from the outer skin of brick. Having such a low thermal conductivity makes it impossible to use the outer wall as the back of the stove’s housing unless a means of ensuring that non of the heat from the stove is transferred to the house wall.
Nestor Martin Stoves
Ideal Installation Cowl to prevent ingress of rain, birds and to assist Flue liner reaching to with flue stabilization top of the termination and insulated Flue liner support collar Weatherproof chimney which is required for both pot and parged at a flexible and single wall steep angle to disperse liners. Installation of Flue Spigot to Flue Pipe The flue spigot is mounted internally within the top of the stove retained by four bolts, see picture below. The top chamber baffle may be in place and will need to be removed to gain access to fit the flue spigot. This baffle is held in place by two bolts and the baffle MUST be replaced once the flue has been connected. The Hearth and Fire Surround Whilst the existing regulations require the hearth to protrude in front of a solid fuel appliance by a minimum of 250mm we strongly recommend that this distance should be 300mm.
These rules make provision for the protection of the property in the event of burning fuel falling from the fire, but the height of the fire bed in an open fire or conventional stove is not very high and as the horizontal distance any falling item travels is, amongst other factors, dependant upon the height from which it starts, it should be apparent that anything falling from an. Minimum Air Setting The minimum air screw should be adjusted to supply the maximum air setting, by screwing it in a anti-clockwise direction until the shutter is fully open when resistance to further turning will be felt, before the stove is lit for the first time. Firebox Components Removal of the Top Mica Baffle Plate The top mica baffle is located in the top of the fire box where it sits on the L shaped baffle support lugs which are part of the casting of the left and right side protection plates.
For easier access remove the front fuel guard. Removal of the Rear Protection Plate To remove (1) lift up the plate so it is higher than the lugs on the grate frame and then (2) draw it towards the centre of the fire box. As it is drawn towards the centre twist the edge towards the front of the fire box. Euroheat Technical Team Information from the Euroheat Technical Team Euroheat and Nestor Martin have a policy of continual research and development and reserve the right to modify its appliances without prior notice. We make every effort to ensure that the information provided in this document is correct and accurate at the time of printing.
Need more info? With over 10,000 pages of technical information, spare parts, product shots, news and 1001 other things, - you will not find a more comprehensive solution to your queries, whatever time of the day. Www.euroheat.co.uk Court Farm Business Park, Bishops Frome, Worcestershire WR6 5AY Pre sales: 12.
Having bought a pre-owned Sony FM stereo tuner through eBay, it came without any manuals. It soon became clear that to get the best from this excellent tuner I needed a decent manual because much of the operation was not intuitive to a newboy to hi fi like me. I managed to download the official Sony multi-lingual manual from Owner-Manuals.com with no problem at all - a really quick and easy service. I'm very glad I did because I found out all the operations of the tuner and was then able to not only set it up quickly but also to get much more from it that poke-and-hope trialling would ever achieve. In my book $4.99 very well spent.